📌 Hello everyone,
Fdrsoft & the Station-Drivers team wish you a very happy holiday season and I take this opportunity to thank those who regularly give me donations to improve the site (Jim-B, Romain-L, Helmar-A, .... ). A big THANK YOU for your loyalty. 😉 (Fdrsoft)

--- SURVEY Are you satisfied with the S-D site? ---

Hello to all of you and thank you again for your loyalty,
Today I want to know if you are satisfied with the site since the change of the server and some touch-ups of the color and the change of the theme of the Forum.
Of course I am aware that there may still be work to do but the biggest part is done
Thank you for your answers
www.station-drivers.com/index.php/en/for...th-the-s-d-site#3618

ssd Jmicron JMS583 Sata USB 3.1 Controller Firmware Version 133.0.1.00.06

  • Shonk
  • Shonk аватар
  • Не в сети
  • Super Utilisateur
  • Super Utilisateur
    Enregistré
  • Сообщений: 146
  • Thanks: 54

Re: Jmicron JMS583 Sata USB 3.1 Controller Firmware Version 133.0.1.00.06

9 мес. 2 нед. назад - 9 мес. 2 нед. назад
#2561
How to backup your nvram (config) and then update the firmware whilst keeping your stock nvram (config)


Tick RD Version

Tick Include JMS57x/8x NVRAM
Tick Backup Old Firmware Only

Click Run

You will now backup your old firmware including Nvram
incase you mess anything up

once that is done

Close it

Open again

Tick RD Version
Load File and browse it to the firmware you want to update to
Untick Include JMS57x/8x NVRAM

Click run

It will now flash the latest firmware but leave the old nvram settings intact

Once that is done you can proceed to backup the new firmware with your nvram settings
if you want like i have done below

Latest Firmware with My Nvram
JMS583-STD-Release-v00.02.01.04-Bus Power (Phison PU31).bin

Latest Firmware From the internet
JMS583-STD-Release-v00.02.01.04-Bus Power.bin




Here's My Factory Firmware backup both with and without nvram
you see the crc32 differences

[img
Последнее редактирование: 9 мес. 2 нед. назад пользователем Shonk.

Пожалуйста Войти или Регистрация, чтобы присоединиться к беседе.

  • Laroldski
  • Laroldski аватар
  • Не в сети
  • Best Poster
  • Best Poster
    Enregistré
  • Сообщений: 59
  • Thanks: 6

Re: Jmicron JMS583 Sata USB 3.1 Controller Firmware Version 133.0.1.00.06

9 мес. 2 нед. назад
#2562
@Shonk Thanks for the help I was able to back up my firmware's Bin file for my non RGB JEYI enclosure's,now all I have to do is back up my Unionsine RGB enclosure's Bin file so I can update it's firmware.

Пожалуйста Войти или Регистрация, чтобы присоединиться к беседе.

  • Shonk
  • Shonk аватар
  • Не в сети
  • Super Utilisateur
  • Super Utilisateur
    Enregistré
  • Сообщений: 146
  • Thanks: 54

Re: Jmicron JMS583 Sata USB 3.1 Controller Firmware Version 133.0.1.00.06

9 мес. 2 нед. назад
#2563
I doubt the RGB is anything to do with the JMS583 firmware
but its always better to have a backup and also use the factory nvram
either way

Пожалуйста Войти или Регистрация, чтобы присоединиться к беседе.

  • Laroldski
  • Laroldski аватар
  • Не в сети
  • Best Poster
  • Best Poster
    Enregistré
  • Сообщений: 59
  • Thanks: 6

Re: Jmicron JMS583 Sata USB 3.1 Controller Firmware Version 133.0.1.00.06

9 мес. 2 нед. назад - 9 мес. 2 нед. назад
#2564
I read on Aliexpress that one guy said his RGB didn't work the same after updating his firmware,I going to have to wait about 1 or 2 weeks to update mine because I lent mine out to a friend.

I guess I will have to wait and see what happens to my enclosure,I will be sure to post the result's good or bad,I think I may try baking up the bin file of my RGB enclosure first then flashing it with normal firmware and if the RGB doesn't work right I'll flash it with the back up bin file.
Последнее редактирование: 9 мес. 2 нед. назад пользователем Laroldski.

Пожалуйста Войти или Регистрация, чтобы присоединиться к беседе.

  • Laroldski
  • Laroldski аватар
  • Не в сети
  • Best Poster
  • Best Poster
    Enregistré
  • Сообщений: 59
  • Thanks: 6

Re: Jmicron JMS583 Sata USB 3.1 Controller Firmware Version 133.0.1.00.06

9 мес. 2 нед. назад
#2568
@Shonk Let's say if something goes wrong if you try different firmware with a different bin file and it goes wrong,do you just need to Tik Include JMS57x/8x NVRAM and use your backed up firmware file.

Пожалуйста Войти или Регистрация, чтобы присоединиться к беседе.

Время создания страницы: 0.081 секунд
Работает на Kunena форум