NVME USB drives Realtek RTL9210/RTL9220 Firmware Version 1.xx
- Shonk
-
- Desligado
- Big Poster
-
Enregistré
- Mensagens: 89
- Thanks: 35
- lapis
-
- Desligado
- Newbie
-
Enregistré
- Mensagens: 2
- Thanks: 0
Re: NVME USB drives Realtek RTL9210/RTL9220 Firmware Version 1.xx
11 meses 2 semanas atrás
OK, I suppose that those item descriptions on Aliexpress can't be trusted... 
It was this "CoolFish M2 SSD Case NVMe SATA Dual Protocol" for a bit over 3$.
I suppose there is no way to add SATA support by firmware or some easy mod?
It was this "CoolFish M2 SSD Case NVMe SATA Dual Protocol" for a bit over 3$.
I suppose there is no way to add SATA support by firmware or some easy mod?
Por favor Iniciar sessão ou Criar uma conta para se juntar à conversa.
- Laroldski
-
- Desligado
- Big Poster
-
Enregistré
- Mensagens: 55
- Thanks: 12
Re: NVME USB drives Realtek RTL9210/RTL9220 Firmware Version 1.xx
11 meses 1 semana atrásOK, I suppose that those item descriptions on Aliexpress can't be trusted...
It was this "CoolFish M2 SSD Case NVMe SATA Dual Protocol" for a bit over 3$.
I suppose there is no way to add SATA support by firmware or some easy mod?
@lapis If you want a great ssd enclosure for NVMe ssd's try the one in the link in black it has an RTL9210 controller the other one in grey has a JMS583 controller,their not much more money and way better built then those coolfish ones.
www.aliexpress.com/item/1005006437088311...in.29.27c11802Al6Vvk
Por favor Iniciar sessão ou Criar uma conta para se juntar à conversa.
- ole258
-
- Desligado
- poster 3
-
Enregistré
- Mensagens: 11
- Thanks: 6
Re: NVME USB drives Realtek RTL9210/RTL9220 Firmware Version 1.xx
11 meses 1 semana atrás - 11 meses 1 semana atrás
I have bought a
Lexar E300
NVME enclosure.
Here is the Dump:
In comparison to most other Dumps, there are much values marked as "n/a".
For example:
U2PHY = 02 f4 9b e0 e1
U3PHY = 02 d4 09 00 d5 00 80
DISK_HOTPLUG = 0x0
PINMUX1 = 0x0
PINMUX2 = 0x700
U2_MAXPWR = 0xfa
U3_MAXPWR = 0x0
ASPMDIS = 0x0
For what are these values for?
Is it recommended to add it at the config file?
Here is the Dump:
Atenção: Revelação!
In comparison to most other Dumps, there are much values marked as "n/a".
For example:
U2PHY = 02 f4 9b e0 e1
U3PHY = 02 d4 09 00 d5 00 80
DISK_HOTPLUG = 0x0
PINMUX1 = 0x0
PINMUX2 = 0x700
U2_MAXPWR = 0xfa
U3_MAXPWR = 0x0
ASPMDIS = 0x0
For what are these values for?
Is it recommended to add it at the config file?
Ultima edição : 11 meses 1 semana atrás por ole258.
Por favor Iniciar sessão ou Criar uma conta para se juntar à conversa.
- sdefrwggerg
-
- Desligado
- regular poster
-
Enregistré
- Mensagens: 32
- Thanks: 21