--- SURVEY Are you satisfied with the S-D site? ---
Hello to all of you and thank you again for your loyalty,
Today I want to know if you are satisfied with the site since the change of the server and some touch-ups of the color and the change of the theme of the Forum.
Of course I am aware that there may still be work to do but the biggest part is done
Thank you for your answers
www.station-drivers.com/index.php/en/for...th-the-s-d-site#3618
Marvell AQC113C FourPartID Firmware updater edit
- Shonk
- Autor Subiect
- Deconectat
- Super Utilisateur
-
Enregistré
- Postări: 146
- Thanks: 54
Re: Marvell AQC113C FourPartID Firmware updater edit
acum 1 săptămână 1 ziActive State Power Management (ASPM) Support: L0s and L1
Active State Power Management (ASPM) Status: Disabled
Vă rugăm Autentificare sau Crează un cont să participaţi la discuţie.
- Shonk
- Autor Subiect
- Deconectat
- Super Utilisateur
-
Enregistré
- Postări: 146
- Thanks: 54
Re: Marvell AQC113C FourPartID Firmware updater edit
acum 1 săptămână 1 zithat means secure boot is enalbed i thinkit tells me Failed to initialize HW Interface
i had it earlier rebooted and disabled secure boot and it was fine then
Vă rugăm Autentificare sau Crează un cont să participaţi la discuţie.
- hu4567
- Deconectat
- poster 3
-
Enregistré
- Postări: 10
- Thanks: 4
Re: Marvell AQC113C FourPartID Firmware updater edit
acum 1 săptămână 1 zidid see your edit a bit to latecan you release a zip with every file edited and ready to go with a command
e.g. ini's edited and it will patch the clx on the fly
i dont want to miss anything
and maybe a txt file in there saying what was changed in what file
actually i think i know everything you done
i will make one and try it myself after dinner
here is a zip file: www.dropbox.com/scl/fi/5cr41qmlw91c5j2h2...avr&st=vfgn4pch&dl=0
Vă rugăm Autentificare sau Crează un cont să participaţi la discuţie.
- Shonk
- Autor Subiect
- Deconectat
- Super Utilisateur
-
Enregistré
- Postări: 146
- Thanks: 54
Re: Marvell AQC113C FourPartID Firmware updater edit
acum 1 săptămână 1 ziConnected to device '0000-0A:00.0'
Chip reset completed (boot from flash). Time: 60 ms
Loaded MAC FW Version: 1.0.113
Loaded PHY FW Version: 6.1.2 (reported by MAC FW)
Loaded bundle: 1.3.21
Active State Power Management (ASPM) Support: None
Active State Power Management (ASPM) Status: Disabled
L0s Exit Latency: 2 - 4 us
L1 Exit Latency: 32 - 64 us
Maximum Payload Size Supported: 512 bytes
Maximum Payload Size: 256 bytes
Vă rugăm Autentificare sau Crează un cont să participaţi la discuţie.
- Shonk
- Autor Subiect
- Deconectat
- Super Utilisateur
-
Enregistré
- Postări: 146
- Thanks: 54
Re: Marvell AQC113C FourPartID Firmware updater edit
acum 1 săptămână 1 zi - acum 1 săptămână 16 oreI have been testing different firmware's all evening they all flash and work with no issues that i can see
your mileage may vary though
You just have to run update.bat from a command prompt then shutdown to reload the firmware fully
I ended up making individual flashers only for fenvi cards and cleaned out all of the excess files
wake on lan from a powered off state doesnt work on the stock fenvi 1.3.21 which i think is AQC113-Antigua_Bx-1.3.21_bdp_aqsign.clx
it also doesnt work with AQC113-DirtyWake_Bx_ASPM_Enabled-1.x.xx_bdp_aqsign.clx
so im going to stick with AQC113-Antigua_Bx-1.x.xx_bdp_aqsign.clx
Here's a copy with my Fenvi factory backup included incase there are problems with newer firmware's
mega.nz/file/V2ZRGZ6Q#kdhnKiErNcAFIh6ajM...sYOIu3w0ii4GEhwrZXNs
Of Interest
when i dumped the firmware of both cards in april 2024 to fix the first card
I dumped the first card that was bad but never bothered trimming the file or testing it in any way
I did this earlier
just flashing with flashupdate2 --reflash ATL2-8.0.1_AGENT_sign.CLX bad_card_good_trim.clx (Factory.bat)
put it back to how it was before fixing it (no link as i had done some further messing with the firmware)
running the dump through customclx2 + reflashing with Update.bat
after a powerdown and back up the card seems fine
so you can fix a bad flashed card without any further firmware
if your firmware is doing code 10 in windows
and Error: MAC firmware is not started. Reset status = 0x15000000
you should be able to fully fix it just by flashupdate2 --reflash ATL2-8.0.1_AGENT_sign.CLX your_dump_trim.clx then shutdown
though i think flashing
flashupdate2 --reflash ATL2-8.0.1_AGENT_sign.CLX AQC113-Fenvi_Factory_Dump_1.3.21_bdp_aqsign.clx (my factory dump) then power down
is the only surefire way to ensure all variables are restored to the card before progressing to a newer firmware
and is what i did after i finished testing before moving on to 1.5.42
Vă rugăm Autentificare sau Crează un cont să participaţi la discuţie.