NVME USB drives Realtek RTL9210/RTL9220 Firmware Version 1.xx
- Shonk
-
- Offline
- Big Poster
-
Enregistré
- Príspevky: 89
- Thanks: 35
- lapis
-
- Offline
- Newbie
-
Enregistré
- Príspevky: 2
- Thanks: 0
Re: NVME USB drives Realtek RTL9210/RTL9220 Firmware Version 1.xx
pred 11 mesiacmi 2 týždnami
OK, I suppose that those item descriptions on Aliexpress can't be trusted... 
It was this "CoolFish M2 SSD Case NVMe SATA Dual Protocol" for a bit over 3$.
I suppose there is no way to add SATA support by firmware or some easy mod?
It was this "CoolFish M2 SSD Case NVMe SATA Dual Protocol" for a bit over 3$.
I suppose there is no way to add SATA support by firmware or some easy mod?
Prosím Prihlásiť alebo Registrácia pre zdieľanie konverzácie.
- Laroldski
-
- Offline
- Big Poster
-
Enregistré
- Príspevky: 55
- Thanks: 12
Re: NVME USB drives Realtek RTL9210/RTL9220 Firmware Version 1.xx
pred 11 mesiacmi 1 týždňomOK, I suppose that those item descriptions on Aliexpress can't be trusted...
It was this "CoolFish M2 SSD Case NVMe SATA Dual Protocol" for a bit over 3$.
I suppose there is no way to add SATA support by firmware or some easy mod?
@lapis If you want a great ssd enclosure for NVMe ssd's try the one in the link in black it has an RTL9210 controller the other one in grey has a JMS583 controller,their not much more money and way better built then those coolfish ones.
www.aliexpress.com/item/1005006437088311...in.29.27c11802Al6Vvk
Prosím Prihlásiť alebo Registrácia pre zdieľanie konverzácie.
- ole258
-
- Offline
- poster 3
-
Enregistré
- Príspevky: 11
- Thanks: 6
Re: NVME USB drives Realtek RTL9210/RTL9220 Firmware Version 1.xx
pred 11 mesiacmi 1 týždňom - pred 11 mesiacmi 1 týždňom
I have bought a
Lexar E300
NVME enclosure.
Here is the Dump:
In comparison to most other Dumps, there are much values marked as "n/a".
For example:
U2PHY = 02 f4 9b e0 e1
U3PHY = 02 d4 09 00 d5 00 80
DISK_HOTPLUG = 0x0
PINMUX1 = 0x0
PINMUX2 = 0x700
U2_MAXPWR = 0xfa
U3_MAXPWR = 0x0
ASPMDIS = 0x0
For what are these values for?
Is it recommended to add it at the config file?
Here is the Dump:
Upozornenie: Informácia, ktorú nemusíte chcieť zobraziť!
In comparison to most other Dumps, there are much values marked as "n/a".
For example:
U2PHY = 02 f4 9b e0 e1
U3PHY = 02 d4 09 00 d5 00 80
DISK_HOTPLUG = 0x0
PINMUX1 = 0x0
PINMUX2 = 0x700
U2_MAXPWR = 0xfa
U3_MAXPWR = 0x0
ASPMDIS = 0x0
For what are these values for?
Is it recommended to add it at the config file?
Posledný krát upravené:pred 11 mesiacmi 1 týždňom ole258
Prosím Prihlásiť alebo Registrácia pre zdieľanie konverzácie.
- sdefrwggerg
-
- Offline
- regular poster
-
Enregistré
- Príspevky: 32
- Thanks: 21