Marvell AQC113C FourPartID Firmware updater edit

With Regards to aspm i have it disabled in the bios on all of my machines but the card is reporting the following with your 1.3.33

Active State Power Management (ASPM) Support:                                   L0s and L1
Active State Power Management (ASPM) Status:                                    Disabled

 

admin 写�：:

it tells me Failed to initialize HW Interface
 

that means secure boot is enalbed i think
i had it earlier rebooted and disabled secure boot and it was fine then

Shonk 写�：:

can you release a zip with every file edited and ready to go with a command
e.g. ini's edited and it will patch the clx on the fly
i dont want to miss anything

and maybe a txt file in there saying what was changed in what file

actually i think i know everything you done
i will make one and try it myself after dinner
 

did see your edit a bit to late
here is a zip file:  www.dropbox.com/scl/fi/5cr41qmlw91c5j2h2...avr&st=vfgn4pch&dl=0


 

Fenvi Factory 1.3.21 firmware aspm status

Connected to device '0000-0A:00.0'
Chip reset completed (boot from flash). Time: 60 ms
Loaded MAC FW Version: 1.0.113
Loaded PHY FW Version: 6.1.2 (reported by MAC FW)
Loaded bundle: 1.3.21

Active State Power Management (ASPM) Support: None
Active State Power Management (ASPM) Status: Disabled
L0s Exit Latency: 2 - 4 us
L1 Exit Latency: 32 - 64 us
Maximum Payload Size Supported: 512 bytes
Maximum Payload Size: 256 bytes

You where right it was not erasing the chip before flash that was causing issues on the newpeak.net/Fenvi/Nicgiga card when updating

I have been testing different firmware's all evening they all flash and work with no issues that i can see
your mileage may vary though

You just have to run update.bat from a command prompt then shutdown to reload the firmware fully

I ended up making individual flashers only for fenvi cards and cleaned out all of the excess files

wake on lan from a powered off state doesnt work on the stock fenvi 1.3.21 which i think is AQC113-Antigua_Bx-1.3.21_bdp_aqsign.clx
it also doesnt work with AQC113-DirtyWake_Bx_ASPM_Enabled-1.x.xx_bdp_aqsign.clx
so im going to stick with AQC113-Antigua_Bx-1.x.xx_bdp_aqsign.clx


Here's a copy with my Fenvi factory backup included incase there are problems with newer firmware's
mega.nz/file/V2ZRGZ6Q#kdhnKiErNcAFIh6ajM...sYOIu3w0ii4GEhwrZXNs







Of Interest
when i dumped the firmware of both cards in april 2024 to fix the first card
I dumped the first card that was bad but never bothered trimming the file or testing it in any way

I did this earlier

just flashing with flashupdate2 --reflash ATL2-8.0.1_AGENT_sign.CLX bad_card_good_trim.clx (Factory.bat)
put it back to how it was before fixing it (no link as i had done some further messing with the firmware)

running the dump through customclx2 + reflashing with Update.bat
after a powerdown and back up the card seems fine

so you can fix a bad flashed card without any further firmware

if your firmware is doing code 10 in windows
and Error: MAC firmware is not started. Reset status = 0x15000000
you should be able to fully fix it just by flashupdate2 --reflash ATL2-8.0.1_AGENT_sign.CLX your_dump_trim.clx then shutdown

though i think flashing
flashupdate2 --reflash ATL2-8.0.1_AGENT_sign.CLX AQC113-Fenvi_Factory_Dump_1.3.21_bdp_aqsign.clx (my factory dump) then power down
is the only surefire way to ensure all variables are restored to the card before progressing to a newer firmware

and is what i did after i finished testing before moving on to 1.5.42